Topic: OMC SRX question (Read 518 times)

1FASTLASER · « **on:** September 03, 2007, 01:21:51 PM »

Am looking at the possibility of getting one of the SRX props for my OMC. What I need to know before dropping the beans is ......

Is this prop better suited for lighweight hulls?? I have found out that my hull really likes the nose up to run better numbers. I have been told the SRX is a good prop for getting the bow up. If I have been told wrong please advise.

realdealprops · « **Reply #1 on:** September 05, 2007, 07:22:53 AM »

The SRX is a good prop. However if you are looking for acceleration you will need a Yamaha drag wheel. If you are looking for over all top end speed, a Merc Lighting E.T. or Merc Chopper II is your best bet. All of these props will need to matched and blueprinted to your boat.

1FASTLASER · « **Reply #2 on:** September 09, 2007, 08:37:56 PM »

So if I am reading your post correctly the SRX is not a very good prop for acceleration?

?

realdealprops · « **Reply #3 on:** September 10, 2007, 06:26:52 AM »

The SRX is decent in acceleration, but the Yamaha is better. I help set-up several Allison drag boats. We have tried every prop known to man and the Yamaha is always quicker.

Bass Fishing Forum > General Bass Boat Discussion > Prop Shop > Topic: OMC SRX question
Local Guides All Local Guides Alabama Alaska Arizona Arkansas California Colorado Connecticut DC Delaware Florida Georgia Hawaii Idaho Illinois Indiana Iowa Kansas Kentucky Louisiana Maine Maryland Massachusetts Michigan Minnesota Mississippi Missouri Montana Nebraska Nevada New Hampshire New Jersey New Mexico New York North Carolina North Dakota Ohio Oklahoma Oregon Pennsylvania Rhode Island South Carolina South Dakota Tennessee Texas Utah Vermont Virginia Washington West Virginia Wisconsin Wyoming Laurie Cork Ph. (318)347-7380 You can Email Me Here Mike Cork Ph. (318)560-9827	« previous next » Pages: [1] Go Down Print Author Topic: OMC SRX question (Read 518 times) 0 Members and 1 Guest are viewing this topic. 1FASTLASER Smallmouth Location: Crossett,Arkansas Offline Gender: Posts: 52 OMC SRX question « on: September 03, 2007, 01:21:51 PM » Am looking at the possibility of getting one of the SRX props for my OMC. What I need to know before dropping the beans is ...... Is this prop better suited for lighweight hulls?? I have found out that my hull really likes the nose up to run better numbers. I have been told the SRX is a good prop for getting the bow up. If I have been told wrong please advise. Logged LASER BOATS WITH A MERC PUSHIN IT.........DOESNT GET ANY BETTER THAN THIS realdealprops Smallmouth Location: Chester, Va. Offline Gender: Posts: 394 Baby Bass Re: OMC SRX question « Reply #1 on: September 05, 2007, 07:22:53 AM » The SRX is a good prop. However if you are looking for acceleration you will need a Yamaha drag wheel. If you are looking for over all top end speed, a Merc Lighting E.T. or Merc Chopper II is your best bet. All of these props will need to matched and blueprinted to your boat. Logged 1FASTLASER Smallmouth Location: Crossett,Arkansas Offline Gender: Posts: 52 Re: OMC SRX question « Reply #2 on: September 09, 2007, 08:37:56 PM » So if I am reading your post correctly the SRX is not a very good prop for acceleration?? Logged LASER BOATS WITH A MERC PUSHIN IT.........DOESNT GET ANY BETTER THAN THIS realdealprops Smallmouth Location: Chester, Va. Offline Gender: Posts: 394 Baby Bass Re: OMC SRX question « Reply #3 on: September 10, 2007, 06:26:52 AM » The SRX is decent in acceleration, but the Yamaha is better. I help set-up several Allison drag boats. We have tried every prop known to man and the Yamaha is always quicker. Logged Print Pages: [1] Go Up « previous next » Bass Fishing Forum > General Bass Boat Discussion > Prop Shop > Topic: OMC SRX question	QUICK LINKS UB Home Main Forum Welcome Dock Talk Techniques Rods and Reels Tackle Box Catch of the Day UB Contests Tips and Ideas Sponsor Connection Fishing Reports Charter Members Only Boats 4 Sale BECOME A CHARTER MEMBER SUPPORT UB

News:

Author Topic: OMC SRX question (Read 518 times)