Ultimate Bass ULTIMATE BASS | BASS FISHING CLASSIFIED ADS | CONTACT US    

Bass Fishing information about bass boats, tackle, fishing rods, baitcasters and other reels all about bass fishing.
Please login or register.

Login with username, password and session length
Advanced search  

News:

Tapatalk should be back up. Please report issues -->here<--. Thank you!

Page Down
FREE TACKLE EVERY WEEK

Bass Anglers Magazine - The Best bass fishing magazine on the rack! Subscribe Today and Catch More Bass

NuTech Lures

Doc Irv Custom Baits

Life Vantage

Get Bit Outdoors

Fishing Frenzy Tackle

Bass Anglers Magazine - The Best bass fishing magazine on the rack! Subscribe Today and Catch More Bass



Bass Boats For Sale Free Classified Ads

Laurie Cork
Ph. (318)347-7380
You can Email Me Here

Mike Cork
Ph. (318)560-9827

Pages: [1]   Go Down

Author Topic: Pad to Prop - Power Pole Install  (Read 335 times)

mgeer

  • UB Member
  • *
  • Offline Offline
  • Posts: 2
  • Baby Bass
Pad to Prop - Power Pole Install
« on: October 06, 2017, 10:09:32 AM »

Hey all,

I'm going to be putting on a pair of 8' Power Poles on my
Triton this weekend, well stating tonight! I have an '08 Triton 186 w/150hp Optimax turning a Tempest Plus 23 with no jack-plate.

I took a pad-to-prop(PTP) measurement and found that the prop is currently positioned 5" below the pad. There are 5 mounting holes on the engine bracket, each 3/4" apart, and the motor is currently bolted in the center mounting hole position(3 of 5).
From what I have seen in prior posts is that a 3-blade prop should sit around 3 1/2" but being mindful of maintaining adequate water pressure to the engine.
....So my question is; since I have to remove the motor from the transom for the installation of the Power Pole brackets, should I move the engine to a higher position to reduce the PTP difference and then fine tune the Tempest with the plugs for optimum performance? My hole shot is decent now but I will be adding an additional 64# total to the tail end of the machine so I thought I would post this for commentary.

Thank you in advance for all of your comments.

Regards,
Mike.
Logged

Bud Kennedy

  • Charter Member
  • *****
  • Location: Myrtle Beach, SC
  • Offline Offline
  • Gender: Male
  • Posts: 6,100
  • PFD's and KILL SWITCHES SAVE LIVES
Re: Pad to Prop - Power Pole Install
« Reply #1 on: October 06, 2017, 10:34:51 AM »

We are very good at spending other people's money around here.  Ideally, since you are gonna pull the motor it would be the perfect time to add a Jackplate.  Im most cases a manual plate will do just fine but it may also accommodate the mounting of the power pole brackets on the jack plate as well.  Otherwise you should consider getting to a 3.5" starting position anyway. 

Since you are adding weight to the transom you will notice a hole shot difference.  Not sure how much but I believe it will be noticeable for sure.  Your prop just might be just fine but many in your situation wind up going to a 4 blade just to improve the hole shot.  As they say your results may vary but a jack plate will make future adjustments possible and a heck of a lot easier.
Logged

Princeton_Man

  • CM Forum Staff
  • ***
  • Location: Princeton, WV
  • Online Online
  • Gender: Male
  • Posts: 8,263
  • My Mission is goin' fishin'
    • J.Langridge
Re: Pad to Prop - Power Pole Install
« Reply #2 on: October 06, 2017, 11:50:19 AM »

Like Bid says, We'll gladly help spend your $$!  ~roflmao

Having experienced and learned a few things about props in the past few years I can say I think a jackplate is a must have. Weight changes, prop changes, and even water temps can have an effect on performance. I'd love to have a hydraulic jack plate but I'm just glad I have a jackplate at all.

Welcome to the family!
Logged
Stratos 285 XL Pro 150 Evinrude ETEC

Proud Member LSCR Club

Mike Cork

  • Father Time
  • Admin
  • *****
  • Location: NW Louisiana
  • Offline Offline
  • Gender: Male
  • Posts: 62,806
  • Get the Net it's a Hawg
    • Ultimate Bass
Re: Pad to Prop - Power Pole Install
« Reply #3 on: October 10, 2017, 05:12:55 PM »

A manual jackplate isn't that expensive and gives you tremendous ability to move the motor and dial it in.

Now as far as changing your mounting position. Hard to say if you should or not without knowing your numbers now? What RPM are you hitting, what kind of speed are you getting. How's your performance in corners? Are you blowing out the prop at all?

If you're happy with your performance, and close to your max RPM's I wouldn't change it. If you need every ounce you can get out of her, then I'd say that you are to low. But that's just a guess at this moment.
Logged
Fishing is more than just a hobby

Dobyns Rods - Monster Fishing Tackle
Cork's Reel Service
Pages: [1]   Go Up
 


Monster Fishing Tactle is the best place to buy your tackle needs Check them out online

When Bass Fishing Is More than Just a Hobby - Dobyns Rods

The most innovative and technologically advanced fishing rod blanks on the planet

Get Chomped at Mega Chomp Lure Company and Get The Best Baits for your Money




QUICK LINKS
UB Home
Main Forum
Welcome
Dock Talk
Techniques
Rods and Reels
Tackle Box
Catch of the Day
UB Contests
Tips and Ideas
Sponsor Connection
Fishing Reports
Charter Members Only
Bass Fishing Classified Ads
Boats 4 Sale

BECOME A
CHARTER MEMBER
SUPPORT UB




Find out about the contests before everyone else and know about the latest news first
 
Page Up

Page created in 0.105 seconds with 34 queries.